Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Air Fuel Ratio Sensor

Toyota Tacoma 2015-2018 Service Manual / 2gr-fks Engine Control / Air Fuel Ratio Sensor

Components

COMPONENTS

ILLUSTRATION

Removal

Removal

REMOVAL

PROCEDURE

1. REMOVE AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

(a) Disconnect the air fuel ratio sensor connector.

(b) Disengage the clamp to separate the air fuel ratio sensor wire.

(c) Using SST, remove the air fuel ratio sensor from the exhaust manifold sub-assembly RH.

SST: 09224-00011

2. REMOVE AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

(a) Disconnect the air fuel ratio sensor connector.

(b) Disengage the clamp to separate the air fuel ratio sensor wire.

(c) Using SST, remove the air fuel ratio sensor from the exhaust manifold sub-assembly LH.

SST: 09224-00011

Inspection

INSPECTION

PROCEDURE

1. INSPECT AIR FUEL RATIO SENSOR

(a) Measure the resistance according to the value(s) in the table below.

Text in Illustration

*A

for Bank 1 Sensor 1

*B

for Bank 2 Sensor 1

*a

Component without harness connected

(Air Fuel Ratio Sensor)

Standard Resistance (for Bank 1 Sensor 1):

Tester Connection

Condition

Specified Condition

1 (HA1A) - 2 (+B)

20В°C (68В°F)

1.6 to 3.2 О©

1 (HA1A) - 4 (A1A-)

Always

10 kО© or higher

Standard Resistance (for Bank 2 Sensor 1):

Tester Connection

Condition

Specified Condition

1 (HA2A) - 2 (+B)

20В°C (68В°F)

1.6 to 3.2 О©

1 (HA2A) - 4 (A2A-)

Always

10 kО© or higher

If the result is not as specified, replace the air fuel ratio sensor.

Installation

INSTALLATION

PROCEDURE

1. INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page ).

(a) Using SST, install the air fuel ratio sensor to the exhaust manifold sub-assembly RH.

Text in Illustration

*a

Torque Wrench Fulcrum Length

SST: 09224-00011

Torque:

Specified tightening torque :

44 NВ·m {449 kgfВ·cm, 32 ftВ·lbf}

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (See page When using SST (fulcrum length of 30 mm (1.18 in.)) + torque ).
  • When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 38 N*m (384 kgf*cm, 28 ft.*lbf)

(b) Engage the clamp to install the air fuel ratio sensor wire.

(c) Connect the air fuel ratio sensor connector.

2. INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See page ).

(a) Using SST, install the air fuel ratio sensor to the exhaust manifold sub-assembly LH.

Text in Illustration

*a

Torque Wrench Fulcrum Length

SST: 09224-00011

Torque:

Specified tightening torque :

44 NВ·m {449 kgfВ·cm, 32 ftВ·lbf}

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench (See page When using SST (fulcrum length of 30 mm (1.18 in.)) + torque ).
  • When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 38 N*m (384 kgf*cm, 28 ft.*lbf)

(b) Engage the clamp to install the air fuel ratio sensor wire.

(c) Connect the air fuel ratio sensor connector.

Accelerator Pedal
Components COMPONENTS ILLUSTRATION On-vehicle Inspection ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT ACCELERATOR PEDAL SENSOR ASSEMBLY (a) Connect the Techstream to the DLC3. (b) Turn the ...

Camshaft Oil Control Solenoid
...

Other materials:

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each sy ...

Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) (P0776)
SYSTEM DESCRIPTION The ECM uses the vehicle speed signal and signals from the transmission revolution sensors (NT, SP2) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of t ...

Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter
DESCRIPTION for Navigation Function: The navigation receiver assembly receives a vehicle speed signal from the combination meter assembly and sends the signal to navigation receiver assembly. for Automatic Sound Levelizer (ASL): This circuit is necessary for the Aut ...

2015-2023 © Copyright www.luting.site