Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Ambient Temperature Sensor

Components

COMPONENTS

ILLUSTRATION

Inspection

Inspection

INSPECTION

PROCEDURE

1. INSPECT AMBIENT TEMPERATURE SENSOR

(a) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

1 - 2

10В°C (50В°F)

3.00 to 3.73 kО©

1 - 2

15В°C (59В°F)

2.45 to 2.88 kО©

1 - 2

20В°C (68В°F)

1.95 to 2.30 kО©

1 - 2

25В°C (77В°F)

1.60 to 1.80 kО©

1 - 2

30В°C (86В°F)

1.28 to 1.47 kО©

1 - 2

35В°C (95В°F)

1.00 to 1.22 kО©

1 - 2

40В°C (104В°F)

0.80 to 1.00 kО©

1 - 2

45В°C (113В°F)

0.65 to 0.85 kО©

1 - 2

50В°C (122В°F)

0.50 to 0.70 kО©

1 - 2

55В°C (131В°F)

0.44 to 0.60 kО©

1 - 2

60В°C (140В°F)

0.36 to 0.50 kО©

NOTICE:

  • Even slightly touching the sensor may change the resistance value. Be sure to hold the sensor connector.
  • When measuring, the sensor temperature must be the same as the ambient temperature.

HINT:

As the temperature increases, the resistance decreases (see the graph).

If the resistance is not as specified, replace the ambient temperature sensor.

Removal

REMOVAL

PROCEDURE

1. REMOVE RADIATOR GRILLE

2. REMOVE AMBIENT TEMPERATURE SENSOR 2. REMOVE AMBIENT TEMPERATURE SENSOR

2. REMOVE AMBIENT TEMPERATURE SENSOR

(a) Disengage the harness clamp.

(a) Disengage the harness clamp.

(b) Disconnect the connector and remove the ambient temperature sensor.

Installation

INSTALLATION

PROCEDURE

1. INSTALL AMBIENT TEMPERATURE SENSOR

(a) Engage the harness clamp and install the ambient temperature sensor.

(a) Engage the harness clamp and install the ambient temperature sensor.

(b) Connect the connector.

2. INSTALL RADIATOR GRILLE

Blower Motor Controller Blower Motor Controller

Air Outlet Control Servo Motor
Inspection INSPECTION PROCEDURE 1. INSPECT MODE CONTROL SERVO MOTOR (a) Inspect the servo motor operation. (1) When 12V is applied between terminals 4 (IGN) and 1 (GND), and 0V ...

Blower Motor Controller
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (See page ) 2. REMOVE INSTRUMENT LOWER PANEL ASSEMBLY 3. REMOVE ...

Other materials:

Diagnosis System
DIAGNOSIS SYSTEM DIAGNOSIS FUNCTION (a) The diagnosis function turns off the cruise control indicator, illuminates the master warning light and displays a warning message when a malfunction is detected. When a malfunction is detected in the dynamic radar cruise control system, DTCs are store ...

Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) (P2769,P2770)
DESCRIPTION Shift solenoid valve SL is turned on and off by signals from the ECM to control the hydraulic pressure acting on the lock-up relay valve, which then controls operation of the lock-up clutch. DTC No. DTC Detection Condition Trouble Area ...

Open in Rear Floor Electrical Key Oscillator Circuit (B27A6)
DESCRIPTION The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 2 indoor electrical key antenna assembly (rear floor). For the No. 2 indoor electrical key antenna assembly (rear floor) to detect when the electrical key transmitter sub- ...

2015-2022 © Copyright www.luting.site