Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Engine Oil Cooler

Components

COMPONENTS

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

ILLUSTRATION

Inspection

Inspection

INSPECTION

PROCEDURE

1. INSPECT OIL COOLER ASSEMBLY

(a) Check the oil cooler assembly for damage and clogging.

If necessary, replace the oil cooler assembly.

Installation

INSTALLATION

PROCEDURE

1. INSTALL OIL COOLER ASSEMBLY

(a) Install 2 new gaskets to the oil bracket sub-assembly.

(b) Install the oil cooler assembly with the 2 bolts and 2 nuts.

Torque:

21 NВ·m {214 kgfВ·cm, 15 ftВ·lbf}

2. CONNECT NO. 1 WATER BY-PASS PIPE SUB-ASSEMBLY

(a) Connect the No. 1 water by-pass pipe sub-assembly.

3. INSTALL FAN SHROUD

4. INSTALL NO. 1 RADIATOR HOSE

4. INSTALL NO. 1 RADIATOR HOSE

5. INSTALL V-BANK COVER SUB-ASSEMBLY

5. INSTALL V-BANK COVER SUB-ASSEMBLY

6. ADD ENGINE OIL 6. ADD ENGINE OIL

6. ADD ENGINE OIL

7. CHECK ENGINE OIL LEVEL

7. CHECK ENGINE OIL LEVEL

8. ADD ENGINE COOLANT

8. ADD ENGINE COOLANT

9. INSPECT FOR ENGINE OIL LEAK

9. INSPECT FOR ENGINE OIL LEAK

10. INSPECT FOR COOLANT LEAK

10. INSPECT FOR COOLANT LEAK

11. INSTALL RADIATOR SUPPORT TO FRAME SEAL

11. INSTALL RADIATOR SUPPORT TO FRAME SEAL

12. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

12. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

13. INSTALL NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Off Road Package)

Removal

REMOVAL

PROCEDURE

1. REMOVE NO. 2 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Off Road Package)

2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

3. REMOVE RADIATOR SUPPORT TO FRAME SEAL

4. DRAIN ENGINE COOLANT

4. DRAIN ENGINE COOLANT

5. DRAIN ENGINE OIL

5. DRAIN ENGINE OIL

6. REMOVE V-BANK COVER SUB-ASSEMBLY

6. REMOVE V-BANK COVER SUB-ASSEMBLY

7. REMOVE NO. 1 RADIATOR HOSE 7. REMOVE NO. 1 RADIATOR HOSE

7. REMOVE NO. 1 RADIATOR HOSE

8. REMOVE FAN SHROUD

8. REMOVE FAN SHROUD

9. DISCONNECT NO. 1 WATER BY-PASS PIPE SUB-ASSEMBLY

9. DISCONNECT NO. 1 WATER BY-PASS PIPE SUB-ASSEMBLY

(a) Disconnect the No.1 water by-pass pipe sub-assembly.

10. REMOVE OIL COOLER ASSEMBLY

(a) Remove the 2 bolts, 2 nuts and oil cooler assembly.

(b) Remove the 2 gaskets.

2gr-fks Lubrication
...

Lubrication System
On-vehicle Inspection ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT ENGINE OIL LEVEL (a) Warm up the engine, and then stop the engine and wait for 5 minutes. (b) Check that the engine oil level is ...

Other materials:

Cruise Control Main Switch
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE STEERING PAD ASSEMBLY (See page ) 2. REMOVE CRUISE CONTROL MAIN SWITCH (a) Disconnect the connector and remove the 2 screws. (b) Remove the cruise ...

Diagnosis System
DIAGNOSIS SYSTEM 1. CHECK DLC3 (a) Check the DLC3 (See page ). 2. INSPECT BATTERY VOLTAGE (a) Measure the battery voltage. Standard Voltage: 11 to 14 V If the voltage is below 11 V, recharge or replace the battery. 3. SELF-DIAGNOSTIC MODE (OPERATING IGNITION KEY CYLINDER) (a) Switch to se ...

Front Airbag Sensor LH Circuit Malfunction (B1615/14)
DESCRIPTION The front airbag sensor LH consists of parts such as the diagnostic circuit and the frontal detection sensor. When the airbag sensor assembly receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated. DTC B1615/14 is set when a ...

2015-2023 © Copyright www.luting.site