Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: PTC Heater Circuit

DESCRIPTION

PTC HTR heater relays are closed in accordance with signals from the air conditioning amplifier assembly and power is supplied to the quick heater assembly installed on the radiator heater unit.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE

1.

PERFORM ACTIVE TEST USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Air Conditioner / Active Test.

(e) Check the operation by referring to the table below.

Air Conditioner

Tester Display

Test Part

Control Range

Diagnostic Note

Heater Active Level

Quick heater assembly

Min.: 0, Max.: 3

-

OK:

Heater Active Level changes normally.

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

OK

2.

INSPECT PTC HTR RELAY

(a) Remove the PTC HTR relays.

(b) Inspect the PTC HTR relays (See page ).

NG

REPLACE PTC HTR RELAY

OK

3.

CHECK HARNESS AND CONNECTOR (PTC HTR RELAY - POWER SOURCE CIRCUIT)

(a) Remove the PTC HTR relays.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

PTC HTR NO. 1

Tester Connection

Condition

Specified Condition

PTC HTR NO. 1-1 - Body ground

Always

11 to 14 V

PTC HTR NO. 1-5 - Body ground

Always

11 to 14 V

PTC HTR NO. 2

Tester Connection

Condition

Specified Condition

PTC HTR NO. 2-1 - Body ground

Always

11 to 14 V

PTC HTR NO. 2-5 - Body ground

Always

11 to 14 V

PTC HTR NO. 3

Tester Connection

Condition

Specified Condition

PTC HTR NO. 3-1 - Body ground

Always

11 to 14 V

PTC HTR NO. 3-5 - Body ground

Always

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

CHECK HARNESS AND CONNECTOR (PTC HTR RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

(a) Remove the PTC HTR relays.

(b) Disconnect the A14 air conditioning amplifier assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

PTC HTR NO. 1

Tester Connection

Condition

Specified Condition

PTC HTR NO. 1-2 - A14-15 (PTC1)

Always

Below 1 О©

PTC HTR NO. 1-2 or A14-15 (PTC1) - Body ground

Always

10 kО© or higher

PTC HTR NO. 2

Tester Connection

Condition

Specified Condition

PTC HTR NO. 2-2 - A14-14 (PTC2)

Always

Below 1 О©

PTC HTR NO. 2-2 or A14-14 (PTC2) - Body ground

Always

10 kО© or higher

PTC HTR NO. 3

Tester Connection

Condition

Specified Condition

PTC HTR NO. 3-2 - A14-13 (PTC3)

Always

Below 1 О©

PTC HTR NO. 3-2 or A14-13 (PTC3) - Body ground

Always

10 kО© or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

5.

CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - PTC HTR RELAY AND BODY GROUND)

(a) Remove the PTC HTR relays.

(b) Disconnect the Q1 quick heater assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

PTC HTR NO. 1

Tester Connection

Condition

Specified Condition

PTC HTR NO. 1-3 - Q1-3 (B)

Always

Below 1 О©

Q1-2 (E) - Body ground

Always

Below 1 О©

Q1-4 (E) - Body ground

Always

Below 1 О©

PTC HTR NO. 1-3 or Q1-3 (B) - Body ground

Always

10 kО© or higher

PTC HTR NO. 2

Tester Connection

Condition

Specified Condition

PTC HTR NO. 2-3 - Q1-1 (B)

Always

Below 1 О©

Q1-2 (E) - Body ground

Always

Below 1 О©

PTC HTR NO. 2-3 or Q1-1 (B) - Body ground

Always

10 kО© or higher

PTC HTR NO. 3

Tester Connection

Condition

Specified Condition

PTC HTR NO. 3-3 - Q1-5 (B)

Always

Below 1 О©

Q1-4 (E) - Body ground

Always

Below 1 О©

PTC HTR NO. 3-3 or Q1-5 (B) - Body ground

Always

10 kО© or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

6.

INSPECT QUICK HEATER ASSEMBLY

(a) Remove the quick heater assembly (See page (b) Inspect the quick heater assembly (See page ).

(b) Inspect the quick heater assembly (See page ).

OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE QUICK HEATER ASSEMBLY

Compressor Lock Sensor Circuit (B1422)
SYSTEM DESCRIPTION The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication. The air conditioning amplifier assembly reads the difference between comp ...

Air Conditioning Unit
...

Other materials:

Speaker Circuit
DESCRIPTION If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers. Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers. If a ...

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE REAR PROPELLER SHAFT BOOT CLAMP (a) Place matchmarks on the propeller shaft and sleeve yoke. Text in Illustration *1 Rear Propeller Shaft Boot Clamp *2 Rear Sliding Shaft ...

Traction Off Switch
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE ROOF CONSOLE BOX ASSEMBLY (See page ) 2. REMOVE A-TRAC SWITCH (TRACTION CONTROL SWITCH) (a) Disconnect the A-TRAC switch (traction control switch) connector. (b) Using a screwdriver, detach the 2 claws ...

2015-2022 © Copyright www.luting.site