Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Rear Combination Light Assembly

Toyota Tacoma 2015-2018 Service Manual / Lighting / Rear Combination Light Assembly

Components

COMPONENTS

ILLUSTRATION

Disassembly

Disassembly

DISASSEMBLY

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for both the LH and RH sides.
  • The procedure described below is for the LH side.

PROCEDURE

1. REMOVE TAIL AND TURN SIGNAL LIGHT BULB

(a) Turn the tail and turn signal light socket with the tail and turn signal light bulb in the direction indicated by the arrow shown in the illustration to remove them.

(b) Remove the tail and turn signal light bulb from the tail and turn signal light socket.

2. REMOVE TAIL AND STOP LIGHT BULB

(a) Turn the tail and stop light socket with the tail and stop light bulb in the direction indicated by the arrow shown in the illustration to remove them.

(b) Remove the tail and stop light bulb from the tail and stop light socket.

3. REMOVE BACK UP LIGHT BULB

(a) Turn the back up light socket with the back up light bulb in the direction indicated by the arrow shown in the illustration to remove them.

(b) Remove the back up light bulb from the back up light socket.

Reassembly

REASSEMBLY

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for both the LH and RH sides.
  • The procedure described below is for the LH side.

PROCEDURE

1. INSTALL BACK UP LIGHT BULB

(a) Install the back up light bulb to the back up light socket.

(b) Turn the back up light socket with back up light bulb in the direction indicated by the arrow shown in the illustration to install them.

2. INSTALL TAIL AND STOP LIGHT BULB

(a) Install the tail and stop light bulb to the tail and stop light socket.

(b) Turn the tail and stop light socket with tail and stop light bulb in the direction indicated by the arrow shown in the illustration to install them.

3. INSTALL TAIL AND TURN SIGNAL LIGHT BULB

(a) Install the tail and turn signal light bulb to the tail and turn signal light socket.

(b) Turn the tail and turn signal light socket with tail and turn signal light bulb in the direction indicated by the arrow shown in the illustration to install them.

Removal

REMOVAL

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for both the LH and RH sides.
  • The procedure described below is for the LH side.

PROCEDURE

1. REMOVE REAR COMBINATION LIGHT ASSEMBLY

(a) Remove the 2 bolts.

(b) Disengage the 2 pins to separate the rear combination light assembly.

(c) Disengage the 2 guides to separate the wire harness.

(d) Disconnect the 3 connectors to remove the rear combination light assembly.

Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for both the LH and RH sides.
  • The procedure described below is for the LH side.

PROCEDURE

1. INSTALL REAR COMBINATION LIGHT ASSEMBLY

(a) Connect the 3 connectors.

(b) Engage the 2 guides to install the wire harness.

(c) Engage the 2 pins to install the rear combination light assembly.

(d) Install the 2 bolts.

Torque:

4.1 NВ·m {42 kgfВ·cm, 36 inВ·lbf}

Personal Light Assembly
Components COMPONENTS ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL MAP LIGHT BULB (a) Install the 2 map light bulbs to the 2 map light sockets. (b) Turn the 2 m ...

Rear Door Courtesy Switch
Inspection INSPECTION PROCEDURE 1. INSPECT REAR DOOR COURTESY SWITCH (a) Check the resistance. (1) Measure the resistance using an ohmmeter, and check the results in accordance with the value ...

Other materials:

Brake Switch "A" Circuit (P0571)
DESCRIPTION Detection condition 1: When the brake pedal is depressed, the stop light switch assembly outputs a signal to the ECM. When the ECM receives the signal, it cancels control of vehicle speed by the dynamic radar cruise control system. The fail-safe function operates to ...

System Description
SYSTEM DESCRIPTION 1. WIRELESS DOOR LOCK CONTROL SYSTEM The wireless door lock control system functions to lock and unlock all the doors from a distance. The system is controlled by a door control transmitter module set sub-assembly which sends radio waves to the door control receiver. The mai ...

Pressure Control Solenoid "B" Circuit Open (P077513)
DESCRIPTION Changing from 1st to 6th is performed by the ECM turning shift solenoid valves SL1, SL2, SL3 and SL4 on and off. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated ...

2015-2022 © Copyright www.luting.site