Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Reassembly

REASSEMBLY

CAUTION / NOTICE / HINT

NOTICE:

When installing, coat the parts indicated by the arrows with power steering fluid (See page PROCEDURE ).

PROCEDURE

1. INSTALL VANE PUMP HOUSING OIL SEAL

(a) Coat a new vane pump housing oil seal lip with power steering fluid.

(a) Coat a new vane pump housing oil seal lip with power steering fluid.

(b) Using SST and a press, install a new oil seal.

SST: 09950-60010

09951-00280

SST: 09950-70010

09951-07100

NOTICE:

Make sure that the oil seal is installed facing in the correct direction.

2. INSTALL PULLEY SHAFT SUB-ASSEMBLY

(a) Coat the bushing inner surface of the vane pump housing front with power

(a) Coat the bushing inner surface of the vane pump housing front with power steering fluid.

(b) Gradually insert the vane pump shaft.

NOTICE:

Do not damage the vane pump housing oil seal lip in the vane pump housing front.

3. INSTALL VANE PUMP SIDE PLATE FRONT

(a) Coat a new O-ring with power steering fluid and install it onto the vane

(a) Coat a new O-ring with power steering fluid and install it onto the vane pump housing front.

(b) Coat a new O-ring with power steering fluid and install it onto the side plate.

(c) Align the dent of the side plate with that of the vane pump housing front and install the side plate.

NOTICE:

Make sure that the side plate is installed facing the correct direction.

4. INSTALL VANE PUMP CAM RING

(a) Align the dent of the cam ring with that of the side plate and install the

(a) Align the dent of the cam ring with that of the side plate and install the cam ring with the inscribed mark facing outward.

5. INSTALL VANE PUMP ROTOR

(a) Install the vane pump rotor with the inscribed mark facing outward.

(a) Install the vane pump rotor with the inscribed mark facing outward.

(b) Coat the 10 vane plates with power steering fluid.

(c) Install the vane plates with the round ends facing outward.

(d) Using a snap ring expander, install a new snap ring onto the pulley shaft.

6. INSTALL VANE PUMP HOUSING REAR

(a) Coat a new O-ring with power steering fluid and install it onto the vane pump housing rear.

(b) Align the straight pin of the vane pump housing rear with the dents of the cam ring, side plate and vane pump housing front, and install the vane pump housing rear with the 4 bolts.

Torque:

22 NВ·m {224 kgfВ·cm, 16 ftВ·lbf}

7. INSPECT PRELOAD

(a) Check that the pump rotates smoothly without making any abnormal noises.

(a) Check that the pump rotates smoothly without making any abnormal noises.

(b) Provisionally install the service bolt.

Recommended service bolt:

Thread diameter

10 mm (0.3937 in.)

Thread pitch

1.25 mm (0.0492 in.)

Bolt length

50 mm (1.9685 in.)

(c) Using a torque wrench, check the pump rotating torque.

Torque:

0.27 NВ·m {2.8 kgfВ·cm, 2.4 inВ·lbf}

or less

8. INSTALL POWER STEERING OIL PRESSURE SWITCH

(a) Coat the O-ring with power steering fluid and install it onto the power steering oil pressure switch.

(b) Install the power steering oil pressure switch onto the vane pump assembly.

Torque:

21 NВ·m {214 kgfВ·cm, 15 ftВ·lbf}

9. INSTALL FLOW CONTROL VALVE

(a) Coat the compression spring and flow control valve with power steering fluid.

(a) Coat the compression spring and flow control valve with power steering fluid.

(b) Install the compression spring and flow control valve.

(c) Coat a new O-ring with power steering fluid and install it onto the pressure port union.

(d) Install the pressure port union.

Torque:

69 NВ·m {704 kgfВ·cm, 51 ftВ·lbf}

10. INSTALL VANE PUMP OIL RESERVOIR SUB-ASSEMBLY

(a) Coat a new O-ring with power steering fluid, and install it onto the vane pump oil reservoir.

(b) Install the vane pump oil reservoir with the 3 bolts.

Torque:

9.0 NВ·m {92 kgfВ·cm, 80 inВ·lbf}

Installation
INSTALLATION PROCEDURE 1. INSTALL VANE PUMP (a) Install the vane pump assembly with the 2 bolts. Torque: 21 NВ·m {214 kgfВ·cm, 15 ftВ·lbf} (b) Connect the oil pressure switch conne ...

Steering Column
...

Other materials:

Front Airbag Sensor RH Circuit Malfunction (B1610/13)
DESCRIPTION The front airbag sensor RH consists of parts such as the diagnostic circuit and the frontal detection sensor. When the airbag sensor assembly receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated. DTC B1610/13 is set when a ...

Inspection
INSPECTION PROCEDURE 1. INSPECT OIL CLEARANCE (a) Using a micrometer and caliper gauge, measure the oil seal clearance. Standard clearance: 0.021 to 0.043 mm (0.0008 to 0.0017 in.) Maximum clearance: 0.07 mm (0.0028 in.) If it is greater than the maximum, replace the vane pump assembly. ...

Data List / Active Test
DATA LIST / ACTIVE TEST 1. DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals ...

2015-2023 © Copyright www.luting.site