Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Reassembly

REASSEMBLY

PROCEDURE

1. INSTALL COMPRESSOR PICK UP SENSOR

(a) Install the compressor pick up sensor with the 3 screws.

(b) Engage the clamp.

2. INSTALL MAGNET CLUTCH ASSEMBLY

(a) Secure the cooler compressor assembly in a vise between aluminum plates.

(a) Secure the cooler compressor assembly in a vise between aluminum plates.

(b) Install the magnet clutch stator with the parts shown in the illustration.

(c) Using a snap ring expander, install a new snap ring with the chamfered side facing up.

*a

Inside

(d) Connect the connector.

(e) Install the screw.

(f) Using a snap ring expander, install the magnet clutch rotor and a new snap ring with the chamfered side facing up.

Text in Illustration

*a

Inside

NOTICE:

Do not damage the seal cover of the bearing when installing the snap ring.

(g) Install the compressor spacer and magnet clutch hub.

NOTICE:

Do not change the combination of the compressor spacer used before disassembly.

(h) Using SST, hold the magnet clutch hub and install the bolt.

SST: 09985-00260

Torque:

13.5 NВ·m {138 kgfВ·cm, 10 ftВ·lbf}

NOTICE:

Make sure that there is no foreign matter or oil on the compressor shaft, bolt, and clutch hub.

3. INSTALL PRESSURE RELIEF VALVE

(a) Apply sufficient compressor oil to a new O-ring and fitting surface of the pressure relief valve.

Compressor oil:

PSD1 or equivalent

(b) Install a new O-ring onto the pressure relief valve.

(c) Install the pressure relief valve.

Torque:

8.0 NВ·m {82 kgfВ·cm, 71 inВ·lbf}

4. INSPECT MAGNET CLUTCH CLEARANCE

(a) Secure the cooler compressor assembly in a vise between aluminum plates.

Text in Illustration

*a

Component without harness connected

(Magnet Clutch Assembly)

(b) Set the dial indicator to the magnet clutch hub.

(c) Connect the battery positive lead to terminal 1 (MG+) of the magnet clutch connector and the negative lead to the ground wire. Turn the magnet clutch on and off and measure the clearance.

Standard clearance:

0.30 to 0.60 mm (0.012 to 0.024 in.)

If the measured value is not within the standard clearance, remove the magnet clutch hub and adjust the clearance using compressor spacer to obtain the standard clearance.

Compressor spacer thickness:

0.2 mm (0.008 in.)

0.3 mm (0.012 in.)

0.5 mm (0.020 in.)

NOTICE:

Adjustment should be performed with 3 or less magnet clutch washers.

(d) Remove the compressor and magnetic clutch from the vise.

Inspection
INSPECTION PROCEDURE 1. INSPECT MAGNET CLUTCH ASSEMBLY (a) Inspect the magnet clutch assembly. Text in Illustration *a Component without harness c ...

Installation
INSTALLATION PROCEDURE 1. ADJUST COMPRESSOR OIL (a) for HFC-134a (R134a): (1) When replacing the compressor and magnetic clutch with new ones, after gradually discharging the refrigerant gas fro ...

Other materials:

Operation Check
OPERATION CHECK 1. CHECK PANEL & STEERING SWITCH HINT: The radio and display receiver assembly panel switches and steering switches are checked in the following procedure. Illustrations may differ from the actual vehicle screen depending on the device settings and options. ...

Inspection
INSPECTION PROCEDURE 1. INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY (AIR CONDITIONING CONTROL ASSEMBLY) (a) Check the resistance. (1) Measure the resistance according to the value(s) in the table below. Text in Illustration *a Component withou ...

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH and LH sides. The procedure listed below is for the LH side. PROCEDURE 1. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY (a) Install the front No. 1 speaker assembly with the 4 screws. NOTICE: Do not touch t ...

2015-2022 © Copyright www.luting.site